Rev 10

[Spud 7]

So which one would you use ? These were both pre wired in there, I have an idea, but just confirming.

 

Thanks

Edited March 7, 2012 by Spud

[truekaotik 458]

Stick a junk speaker on one set, go to where u mount your amp and the speaker wire is. Take one wire and put it on the ground of a dewalt or any type of 7-14.4 volt drill battery, then tap the other wire to positive. The speaker will pop if it's the right wire... There are other ways to test but this is the fastest and easiest... I really don't know other than guessing which is the right wire for those towers, so I would test pop a junk speaker...

Edited March 7, 2012 by truekaotik

[Spud 7]

Well, they are not connected to anything, they are spooled and zip tied at floor. I am assuming match up the red/blk with rev 10's tens red/blk and 86 the clear wire.?. It's same guage as rev 10's, I just don't know why Centurion would run both.

[truekaotik 458]

Btw spud it won't blow the speakers doing this. I've used the same factory speaker out of a car for doing this for 6 years, and also use to test to make sure speaker wires are still live on non working speakers that come in and it plays fine . Any old speaker will work....

[truekaotik 458]

It could be for tower lights and speakers, you just don't know which. Or a number of things.. I would test the wire first to make sure.. I would assume also to use the real speaker wire first ( the clear with copper and silver)... The red and black I assume is hot and ground for tower light or neons since they are set up for WETSOUNDS now... I'm guessing and trying to help without being there bro...

Edited March 7, 2012 by truekaotik

[Spud 7]

Ight, thanks bro.

[truekaotik 458]

Hook a speaker up to the clear wire and let it hang. Go inside and unzip tie the wires and hit each one on the battery till it pops. That's your run for that speaker. Mark it.. Move The speaker to the other side and repeat... ;-)

[Wylie_Tunes 146]

The clear shielded wires are the speaker wires, the red and white are for tower lights. The clear wires should be stubbed out an bundled up in the gunwale just below where they come through the deck from the tower. From there, you will probably need to extend them over to your amp.

 

If in doubt, use a DVOM to check for continuity.

[Spud 7]

Cool thanks guys, glad I asked. Been a fun project so far. Post pics when done for sure!

[truekaotik 458]

The clear shielded wires are the speaker wires, the red and white are for tower lights. The clear wires should be stubbed out an bundled up in the gunwale just below where they come through the deck from the tower. From there, you will probably need to extend them over to your amp.

 

If in doubt, use a DVOM to check for continuity.

There ya go spud my guess was right on the clear... :-) lol

If you don't have a dvom which most regular folk don't, my way will work perfectly fine and there is nothing wrong with it...

Edited March 7, 2012 by truekaotik

[truekaotik 458]

Cool thanks guys, glad I asked. Been a fun project so far. Post pics when done for sure!

Good deal brother!! Can't wait for the pics!!

[WakeDoc 471]

2nd clear is for speakers other is for lights

[smitty 0]

I used those to pull in new ones that were the legnth I needed so I didn't have to splice them together. Not necesary but oh well..

[Spud 7]

Yep, all good! the wires coming from 10's confused me.

[jaxcenturion 5]

Yes clear is for speakers, red/blk is for lights or other acc....If you noticed the clear is much more stranded than the red/blk....IMO...The wire they run in junk. I would buy some quality wire and pull it through...I would use 12 ga if you can fit it, it may be a little over kill but its good, if the holes are too small step down to 14ga....That crap they put in the tower corroded and turned green in a matter of months on my boat....Kinda crazy, fresh water, encased wire, and inside the tower...after speakers started having less quality thats what i found.....

 

Also make sure you sauder and shrink wrap wires...will make for much better sound and longevity

[truekaotik 458]

Yep, all good! the wires coming from 10's confused me.

The thick red (+) and black (-) are the speaker wires on the rev10's the other 4 thin wires are for the RGB LED's spud... It's in the manual..

[Spud 7]

Jax thanks. I have them plugged and shrunk wrapped over that. Next fall I am taking the tower off to powder coat it, I really hate that finish it as it collects everything it comes in contact with, so I will rewire all the speakers.

 

Kaotik, thanks as well. I read the manual believe it or not, I'm even the guy who reads the new vehicle manual as well. My main concern was I was not sure if Centurion threw the red and blk in because they knew they were going to Wet Sounds. Just wanted to be 100% sure.

 

Today I continue on !

[truekaotik 458]

SSSWWWEEeTTT spud :-) you have any more problems pm me and we can exchange numbers if something comes up your not sure of...

[Spud 7]

Awesome thank you !

[RVR-RAT 269]

Awesome Spud very nice.