-
Content count
53 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Member Map
Store
Calendar
Classifieds
Everything posted by utilityvehicle
-
Key won’t turn power off to ignition or anything else
utilityvehicle posted a topic in Centurion Boats General Discussion
2014 Centurion FX 44. When I turn the key off it stays running and nothing else will turn off. Faulty ignition? Have to use main power to shut everything off -
No power to gates/trim tab/ blower
utilityvehicle posted a topic in Centurion Boat Maintenance, Performance, Troubleshooting
2014 Centurion FX 44 first time out this year. Ram fill says it’s filling but they are not. On the lift I put it in trailer mode and when opening and closing I hear nothing. Weird the trim tab does nothing and blower too. Worked when I put it away. I do not take batteries out for storage just put tenders on them inside my shop. Lastly the shop replaced my O2 sensor at the end of the season. Any ideas folks. Thank you -
SPRINKLER REPLACEMENT
utilityvehicle posted a topic in Centurion Boat Maintenance, Performance, Troubleshooting
So I replaced my stock Sprinkler valves with Irritrol 2400 Valves that are 24V. I have really good flow out of one of them but the other is not nearly as good. Pulled the filter and the flow is strong there so clearly a valve. They open and close when they are suppose too. Bleeder valves are closed and the manual control is set to off which is clockwise. Any other ideas? Thanks -
2008 Enzo 230 wake plate
utilityvehicle posted a topic in Centurion Boat Accessories, Electronics and Modifications
Just installed my new wake plate and the goofy side is awesome but the regular side has an abnormal amount of spray. It is built exactly like the factory A Plate that screws to the bottom of the hull. -
2008 Enzo 230 wake plate
utilityvehicle replied to utilityvehicle's topic in Centurion Boat Accessories, Electronics and Modifications
Could I bolt a piece onto the wing? Would you bolt or weld it to the bottom vs the top so the ridge does not create splash? Thanks -
2008 Enzo 230 wake plate
utilityvehicle replied to utilityvehicle's topic in Centurion Boat Accessories, Electronics and Modifications
Thanks Shaka. Glad someone else has had the same problem. My wiring is super clean and not a factor. The angle is not quite flush with the hull is is slightly tipped up but maybe could go up a hair more do you think? There is about a 1/4 to half inch gap from the wing to the boat? Could that pick up spray? Thanks again for your help. -
Wanting to buy a Asymmetrical Plate
utilityvehicle posted a topic in Centurion Boat Accessories, Electronics and Modifications
Anyone able to tell me where to purchase one or is someone on the forum making them? Thanks -
Addition of asymmetrical plate.
utilityvehicle replied to Troy's topic in Centurion Boat Accessories, Electronics and Modifications
I also am in Edmonton and would get one. -
Only one port an starboard pimp working
utilityvehicle posted a topic in Centurion Boat Maintenance, Performance, Troubleshooting
Pumps have worked fine all year. Now the one port switch does not fire up the pump to fill and one starboard does not turn the pump on to fill. It's weird because one port and one starboard does work. Boat is a 2008 Enzo 230. -
Only one port an starboard pimp working
utilityvehicle replied to utilityvehicle's topic in Centurion Boat Maintenance, Performance, Troubleshooting
Ok the pump failed so I need a new pump. I have a water puppy 18220-2123 has that pump been subbed to a different number or is it still commonly found? Thanks -
Only one port an starboard pimp working
utilityvehicle replied to utilityvehicle's topic in Centurion Boat Maintenance, Performance, Troubleshooting
LOL Saw that after I hit post. Checked fuses and they are all good. I know the pump works because I have 2 fill buttons for port and starboard sides and one works on each side. Weird that one off each side goes at once? -
Broken swim platform bracket
utilityvehicle replied to Lake Water Connoisseur's topic in Centurion Boat Maintenance, Performance, Troubleshooting
Mine broke too. Had them rewelded and work great now -
Only one port an starboard pimp working
utilityvehicle replied to utilityvehicle's topic in Centurion Boat Maintenance, Performance, Troubleshooting
Sorry. They both empty even though they don't fill -
Both sides filling on ballast
utilityvehicle posted a topic in Centurion Boat Maintenance, Performance, Troubleshooting
For some reason when I fill my SB side the port side is filling now? Never had this issue before and I have not touched a thing over the winter? -
Both sides filling on ballast
utilityvehicle replied to utilityvehicle's topic in Centurion Boat Maintenance, Performance, Troubleshooting
Thanks Guys -
Both sides filling on ballast
utilityvehicle replied to utilityvehicle's topic in Centurion Boat Maintenance, Performance, Troubleshooting
Are they located under the floor or closer to the engine -
Hitting rev limiter. Beeping
utilityvehicle posted a topic in Centurion Boat Maintenance, Performance, Troubleshooting
Pulled the boat out for the first time this year and at full throttle hitting 6000 rpm and then beeps which I am assuming is the rev limiter. Could this be old fuel symptoms. -
Hitting rev limiter. Beeping
utilityvehicle replied to utilityvehicle's topic in Centurion Boat Maintenance, Performance, Troubleshooting
Thanks guys. The more I read the more what your saying is making sense. I have never opened my boat wide open before so maybe not even a new issue. -
08 enzo SV 230 Ballast Question
utilityvehicle replied to Whitece's topic in Centurion Boat Accessories, Electronics and Modifications
I have the exact same boat with enzo sacks and I move a 400lbs bag around on the seats at times. Enzo sacs are great on their own but if shy on people put the extra weight on the seat. -
Help Buying Centurion
utilityvehicle replied to Greg135's topic in Centurion Boats General Discussion
I have an 08 Enzo 230 and we love it. -
Tower lights
utilityvehicle replied to Toddj's topic in Centurion Boat Accessories, Electronics and Modifications
I used the rigid light bar and it works awesome -
get a board bag and you wont have to worry about dings, most of the custom boards dont fit in the racks anyways so bag it and put it under the seat
-
Anyone try one of these yet and have any feed back? Just purchased the siren model and find it a bit slow in comparison to soul crafts but it may be just me?
-
My second week on the board and its coming together, can finally air it and get it to carve really hard. just a big adjustment from a skim but love it now.
-
Installed the 20" light bar this weekend and turned out really good.