Jump to content

Search the Community

Showing results for tags 'RPM'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Feedback, Announcements and Crew Deals
    • Site Announcements
    • Crew Deals
    • Site Feedback & Support
  • CenturionCrew.Com
    • Centurion Boats General Discussion
    • Centurion Boat Accessories, Electronics and Modifications
    • Centurion Boat Maintenance, Performance, Troubleshooting
    • News From Centurion Boats and Dealers!
    • Centurion Boat Owners Hook-Up
  • SupremeCrew.Com
    • Supreme Boats General Discussion
    • Supreme Boat Accessories, Electronics and Modifications
    • Supreme Boat Maintenance, Performance, Troubleshooting
    • News From Supreme Boats and Dealers!
  • General Discussions
    • Watersports & Related Gear
    • Marine Audio
    • Articles by Members
    • Off Topic
    • Boat Shows, Local Events and Gatherings

Marker Groups

  • Members
  • Centurion Boat Dealers
  • Centurion Boats/Fineline Industries

Calendars

There are no results to display.

Categories

  • Boats
  • Gear

Found 6 results

  1. Hello everyone We took out the new boat on Tuesday and wanted to test out the wake surfing capabilities of the boat. We filled all the ballast bags and when we tried to go we noticed we could not get over 3300 RPM's and could not get over 10mph. Also, I see the prop on the boat is an acme 537, which is 13.5 x 16 x 1 1/8. We reset all of the settings on the mercmonitor and went back and changed things and still only topping out at 3300 RPMS. If we have all the ballast empty then we can hit 5000 RPM around 37 mph. When we were on the test drive we had the same amount of people in our boat a didn't have any issues, but when we got it home we had to move everyone to the front of the boat to even get it close to 10mph. Would a new prop help with the RPM issue? Thank you for any help possible!
  2. Looking for prop recommendations to lower the engine rpm while surfing. Ri217 with 6.0l running 4000 rpm while surfing at 11.2mph.
  3. Looking for prop recommendations to lower the engine rpm while surfing. Ri217 with 6.0l running 4000 rpm while surfing at 11.2mph.
  4. I wanted to start a thread for Fi21 owners who have upgraded their stock prop. I've got a 2018 Fi21 with the PCM L96 (409) engine. My stock prop is the ACME 1235 (14.5x14.25). At sea level, I'm seeing about 4100-4300 RPM surfing w/ full ballast & about 10.5-11mph. Top speed is about 33-34 at 4900 RPM. Also, the holeshot is just fine. Anyone gone with a bigger prop to get the RPMs down? Please share your actual experience.
  5. 2012 Enzo - Ok - this just happened yesterday. The MPH and RPM indicators (analog) will pop up on start, then fall all the way to below zero and don't function. Also the Oil Pressure and Water Temp (I think this was the other gauge) on the display don't show any measurements (these are the two vertical "bar graphs" on the display). PLUS my ballast tanks won't fill... I've had my MPH gauge not function in past, but it was the large breaker just above the front battery, however this didn't resolve issue this time. I've checked the breakers under the helm as well as above the batteries - any other location these might be in? I did replace both batteries this past week, but the boat was working just fine since then (just one day). Any ideas??
  6. Have a 2010 falcon v 353. It came with a 537 prop. I can only get 4900 rpm and 40mph. Our lake is at 2800 ft. Thinking of going to a 1433 prop as that is the one listed on the acme site for high elevation.. Anyone try this prop?
×

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy..