HoneyBadger0829

Good Morning, Going to keep this short and sweet. Is there a list of bolt on Fresh Air Exhaust systems for the typical twin 3" stock exhaust as seen below? I am looking for is a site to order from with a quality product. I am open to all ideas. My boat is a 2012 V226 for reference. Thank you in advance

My shaft seal is leaking. Does anyone know the shaft tube outer diameter? The prop shaft is 1.125 and I assume the outer tube is 2" but it's a mean woman to measure accurately. I'm running the ACME 1235 prop. I plan on going with the PYI PSS shaft seal type A part 02-114-200 as I want to do this once. Thanks in advance.

I also live in Seattle and have blistering after a short time in the water. It sucks but I plan to bottom paint this winter. Good luck man!

FAE would be a good option plus it makes it safer while surfing. My motor noise dropped drastically when I installed the FAE.

Thanks, I will start researching props and get it swapped out. I was expecting a slight change in performance but this is a little too much. I'll let you know what I come up with.

Follow up after some time on the new FAE. It works great and is much quieter however, my Hull shot and up to plane is drastically slower. Am I outa luck or is anyone aware of a fix? I have the scorpion 5.7 motor.

My 12 226 came with the paddle wheel and software incorporated into the dash. I just set it and go. I wonder if this was optional on the 13.

I finally installed the FAE. The motor noise is much lower and overall works great.

This past year I bought a new 2012 with 8 hours on it. The guy bought it, put it in his garage and never used it. The first thing I did was have it sent to a mechanic for a full mechanical evaluation. As expected it was fine, but always have a professional look at it. Good luck.

The Seattle boat show starts this weekend so it will be a couple weeks before I pull the boat out of the water. I will post build pics asap. Even on wet chilly days here, I really just want to close my work laptop and boat for the afternoon.

Thanks, InfinitySurf for the link. Here is a pic of everything except the 2 support rods for the platform.

I started working with FAE back in September so I got a fair price with the promotion that was going on then. My FAE FINALLY arrived today, shipping was a bit of a cluster but it's here. I will upload some pics once I figure out how to make my 4000KB photo into a 204.8KB.

I went with picture 1 seen above. I originally wanted the 1-piece Y design because it was a clean look however, when Christine at FAE sent me the worksheet for measurements I said the hell with that. You can only be off by 1/8 inch and the time it would take me to get my trailer out of storage, the boat out of the water, measure etc. I knew I would never do it. Plus, if you measure wrong, you're screwed. The second reason is that since I boat year round, looks don't really matter as long as it functions as designed.

I finally got my FAE ordered and I should have it in a couple weeks. I will put up a few pics once it arrives.

This is why I keep our boat in the lake and I was just out on her last night. Was it chilly? Yes. Was my beverage hot? Yes. Did I turn the heater on? Maybe... Would I do it all over again? HELL YEAH BABY.

Yes, H20king is correct. Mine is a 2012 with dual ports.

Check out this site. http://www.fivestarmanufacturing.com/kat_s I have the battery warmers and 4 of the small heaters. One on each riser one on the pan and the tranny.

Thanks everyone, I finally spoke with FAE and these are the options available. Has anyone had better luck with one specific design over the other? Any performance changes and/or surf quality issues?

DrNate, I assume you are suggesting that the Centurion Dual Exhaust is an exact fit for Supreme Dual Exhaust? I've been checking this site for months and the Supreme page isn't built out yet. I emailed and never got a response from them.

I have the Black Scorpion 350 V8 and wondering what you have used for the oil relocation kit. 1. Did you purchase the OEM version? 2. Since motor is a Chevy small block, sites such as JEGS or Summit Racing have options which are generally much less expensive than the "marine" version. If you have specific kit recommendations, that would be ideal. Thank you in advance and Happy 4th!!!

I recently purchased a 2012 V226 with 7 hours and I just hit the 20 hour mark. (yes, someone bought it and put it in the garage for years). I know my way around a motor but for the life of me I can not find the damn oil filter location. Any ideas? The owners manual shows 3 places but it's not there. The motor is the Black Scorpion Merc 350 V8. Thanks in advance! Ryan

h20king, Thanks for the information, I found the damn thing. It is tucked, hard to get to and the motor is black so naturally they put a black filter on it. I will be buying the remote kit. It's ridiculous that the dealers don't automatically install this kit on all boats. Thanks again and happy boating!!! Ryan

h20king, Thank you for fast response and unfortunately it's not by the riser. I will search low in the bilge and report back. Ryan

I was looking for the same thing with no luck so I went with the super shadow bimini. http://bigairwaketowers.com/bimini/supershadowbimini/