Jump to content

Jlagos

Crew
 View profile  See their activity

  • Content count

    133

  • Joined

  • Last visited

  • Days Won

    7

Everything posted by Jlagos

  1. Glad it's fixed.

  2. Bilge and bouy parking?

    Jlagos replied to DaveInTahoe's topic in Centurion Boats General Discussion

    The bilge is (should be) wired to power at all times EVEN if the batteries are turned off. This ensures the pump always has power should water enter via rain or a leak and the batteries have been turned off. You will often see a small wire attached to the battery post. If you want to check, add enough water to your bigle and turn off the power when the sensor triggers the pump on. It should still run if enough water is still left in the bilge.
  3. Nicely finished. So will the plate beneath the strut change the angle of the thrust produced by the propeller. If so, will it then try to lift the back as you were describing to boardjnky4. How about turning at idle?
  4. Hey cyclone, welcome aboard and thanks for the input
  5. Great point Hokiebob, when something funny us going on electronically I always disconnect power entirely and if stored off the water for extended time I disconnect the battery entirely. I found my cranking battery completely dead and unable to be revived after the float mechanism in the bilge pump got stuck in the on position. Also agree with "Infinity" that Noco makes a great product. I have one of those and also have a "Battery Minder" which works by a different method. It will not quickly charge your deep cycle battery if you want to get back on the water with with your sound system fully charged in a couple of hours but i like it during the winter and when stored.
  6. Congrats. That looks awesome.

  7. I'm Back!

    Jlagos replied to Troy. R's topic in Supreme Boats General Discussion

    It's good your back. I have read many of your posts which were always helpful. Maybe with time others will return and become active again.
  8. That's fantastic. I really like that the ladder in its down position is not completely vertical but at an incline. I will need to do this. When my in-laws clime up the platform, there is a sudden grunt, followed by a thud and sudden expulsion of air released somewhere behind me.
  9. Impressive, that's great work and finish. Factory like in appearance.
  10. Sorry I didn't see the boat was at a different location
  11. So it's very easy to check the pump rate. The black portion is the cartridge that will screw out of the yellow pump housing. The wing like appendages at the top are used to unscrew the cartridge. You dont not remove the housing from your ballast tanks. At 9 o'clock in your picture you can see a locking lever that you need to slightly unlatch. If you dont disengage this latch it will not come out until you break it. Take a look at the Johnson pumps online and you'll see the 2 parts and the unlocking latch that lays horizontally on the housing. Simply disconnect the electrical connection and connect the new one. Once you've done it, you could literally change one in a minute.
  12. Does the same happen when in neutral? Can you rev above 3000 rpms and keep it there for a moment? Rember that in neutral the engine does not demand the same fuel flow as when overload but at least you can tell if the engine can sustain a high rpm. Like volzalum said check the fuel pressure and also check the connections in the fuel pump and sending units. I would try to see and run with the fuel cap off/open. Is a vacuum developing and therefore stalling the engine. Does the engine start immediately after stalling?
  13. Multiple locations on the web will ship very quickly. I just ordered 2 water impeller pumps (one is for next year) from skidim.com and they shipped it that morning. They are located in SC. Depending on where your located it should get there by the weekend. I can't imagine it would be very difficult to change. A couple of hoses and bracket bolts to unscrew. The most difficulty thing is always the accessing the part that needs changing. I believe Skidim may also cross reference the engine you list and help make sure the parts are properly chosen. By the way, never order water pumps, spark plugs (especially the expensive ones), belts and other critical components from Amazon they are notorious for faulty, phony counterfeited products they will break.
  14. Welcome to the crew. My guess is that's the water distribution housing. Within the thread is a link for the replacement part. Your pic appears different but I think its the angle of the picture
  15. You may have to go directly to medallion to get the schematics for the unit. I have never seen wiring diagrams for any of the models but then again I haven't searched for them.

  16. Looking for enzo or avy

    Jlagos replied to Creekrat82's topic in Centurion Boats General Discussion

    Yes I would agree. The deep v wake the wakes a little more difficult to figure out. As people get a little more in age they tend to gravitate to surfing. It's not as rough in the joints
  17. Sorry about the repeat post. Yes you have the transmission and vdrive correctly identified. The engine connects to the transmission and then the vdrive which is the most front portion. It has the brass colored part you see spinning when in gear. I cant get my bearings straight with the picture you sent that has the connections. Like troy said, clean those connections. The pressure sensor I changed looked different https://www.google.com/url?sa=t&source=web&rct=j&url=https://www.nautiqueparts.com/product/vdrive-oil-pressure-switch/&ved=2ahUKEwj3prHb7oHqAhXkTDABHRzQAw4QFjAHegQIBhAB&usg=AOvVaw3-k4JxuYjWZ6pe9O_2Y5cp&cshid=1592157194902
  18. Problem 1: have you checked to see if electrical current is present at the pump when you flip the switch to drain? Your switch maybe bad. I would try visually inspect the drain lines and see how they are plumbed. I know you said you have a reversible puppy but do you also have a pump that drains separately and was disconnected electrically. When you fill maybe your overflowing properly via the overfill line but also pushing water out via a drain pump that is no longer wired? Problem 2: Its possible you have a faulty pressure sensor. My prior boat , a moomba, had Walter's drive and needed a new sensor. Very easy to change. You disconnect 2 wires at the sensor and unscrewed it and then put in the new one. You can also get a pressure gauge that needs to measure the proper range. The Walter's drive i had ran at 2 psi but I never checked the pressure prior to changing.
  19. Problem 1: have you checked to see if electrical current is present at the pump when you flip the switch to drain? I would try visually inspect the drain lines and see how they are plumbed. I know you said you have a reversible puppy but do you also have a pump that drains separately and was disconnected electrically. When you fill maybe your overflowing properly via the overfill line but also pushing water out via a drain pump that is no longer wired? Problem 2: Its possible you have a faulty pressure sensor. My prior boat , a moomba, had Walter's drive and needed a new sensor. Very easy to change. You disconnect 2 wires at the sensor and unscrewed it and then put in the new one. You can also get a pressure gauge that needs to measure the proper range. The Walter's drive i had ran at 2 psi but I never checked the pressure prior to changing.
  20. Volazalum, looks like you were correct it is a Walter's vdrive. Geez Scooper, do you think they sucked out all the lubricants and forgot to fill. Even though you overheated, why is EVERYTHING low. Was engine oil also low? From the partial picture, it appears you have a PCM engine. If so, dexcool should be the proper coolant. If you don't have an engine manual you can download them at the pcm https://pcmengines.com/wp-content/uploads/2017/09/imagesL510010-13.pdf. the transmission dipstick looks to be consistent with 40 series transmission. It is checked with the engine running. Again double check with the manual. When running on the hose you typically dont increase above 1500 rpms as this can cause the hose to collapse and prevent water flow. I would definitely change the impellar.
  21. If the cost difference is $100 -175, I too would choose the new brackets and be done with it for the reasons you stated. I'll have to check mine out this weekend. I have the same boat.
  22. I would also guess your length is 20. A couple of threads may help. You may already seen them. There's also a couple of threads that will help with the change. The # number for your steering cable is in the 1st link www.centurioncrew.com/index.php%3F/forums/topic/11580-need-to-order-steering-cable/%23comment-154999&ved=2ahUKEwjlvPGE5PPpAhWDRDABHdd_AMYQiukCMAx6BAgHEEI&usg=AOvVaw2TlZvPw5hmMo_wYKqcVU_O www.centurioncrew.com/index.php%3F/forums/topic/65-steering-cable/%23comment-378&ved=2ahUKEwjlvPGE5PPpAhWDRDABHdd_AMYQkvECMAx6BAgHEAk&usg=AOvVaw12LvEIVu3wBF5U7wp2YI6x&cshid=1591673492125
  23. What's the price difference for the new brackets compared to the repair?
  24. I have need to change lights but can you access the lights behind the centurion logo by removing a speaker?
  25. It'll cost more but could you send them your old carpet as the template?
×

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy..

  I accept