-
Content count
68 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Member Map
Store
Calendar
Classifieds
Everything posted by Pildo
-
Does anyone know if the high temp alarm has to be cleared to allow the boat to return normal operation from limp mode. I had an impeller go bad and my local pcm dealer replaced it. They said it had to be done and charged $90. Thanks
-
High temp alarm
Pildo replied to Pildo's topic in Centurion Boat Maintenance, Performance, Troubleshooting
That was on top of the 1 hr to change the impeller. I typically change it myself but thought it was a bigger problem this time. -
Not starting after running and getting warm
Pildo replied to Jdills1371's topic in Centurion Boat Maintenance, Performance, Troubleshooting
There is a filter under the idle control valve that could need cleaned or replaced. Also could be the valve itself. I have an extra valve that still works if you want to give it a try. -
"Power plus" v-drive trans....change fluid?
Pildo replied to InfinitySurf's topic in Centurion Boats General Discussion
Thanks for the help -
"Power plus" v-drive trans....change fluid?
Pildo replied to InfinitySurf's topic in Centurion Boats General Discussion
On the transmission fluid do you just suck out the old and replace it with new? Is there a filter to change? -
Does anyone use there on board battery charger? I have a 16 FS44 and do not know if it works when it’s plugged in. Anyone have some tips on using it?
-
On board charger
Pildo replied to Pildo's topic in Centurion Boat Accessories, Electronics and Modifications
where the charger bank is located? -
On board charger
Pildo replied to Pildo's topic in Centurion Boat Accessories, Electronics and Modifications
where the charger bank is located? -
I have a 16 FS 44 and looking to add a rear view camera. Has anyone done this? It looks like the infrastructure may already be in place.
-
I’m in southern IL. You’re welcome to crawl through here. 16 FS 44
-
FS 44 Routine maintenance
Pildo posted a topic in Centurion Boat Maintenance, Performance, Troubleshooting
I bought a new 2016 fs44 this summer with the H6 engine and have a couple of questions. For the annual maintenance do you do it yourself or take it to a dealership? The manual states that states some of the work must be done by a dealership. Has anyone called pcm and asked if you could do the work and keep records on it? The only reason I would take the boat in is to stay compliant on warranty. Thanks in advance. -
FS 44 Routine maintenance
Pildo replied to Pildo's topic in Centurion Boat Maintenance, Performance, Troubleshooting
Thank you for the replies. Is there a filter on the transmission or is it just simply removing the old and putting in new fluid? -
Does anyone know who manufactures the shaft seal that would be on a 2016 fs44 or similar boat?
-
This is the best picture I could get
-
Does anyone know what time of shaft seal would be in a 2016 FS44?
-
07ish air warrior V Drive shaft seal replacement
Pildo replied to Mule's topic in Centurion Boat Maintenance, Performance, Troubleshooting
I replaced my seal on a 06 Enzo with a pss seal. I had to take up floor, pull v drive, and pull shaft out towards the front of boat. It was not a hard just but did take a few hours. -
2000 Centurion elite 350 mag MPI ski won't start when hot
Pildo replied to ed6wwww's topic in Centurion Boat Maintenance, Performance, Troubleshooting
Does your boat have FAE? I had the same issues after installIng FAE.- 9 replies
-
- 350 mag mpi overheat
- 350 mag mpi wont start when hot
- (and 1 more)
-
I am having a prop plate put on my fs44 on Friday due to prop burn. Does anyone know if there is a wait time before I can use the boat? (Possibly due to glue drying, etc).
-
Prop burn plate
Pildo replied to Pildo's topic in Centurion Boat Maintenance, Performance, Troubleshooting
Thank you -
Are there two drain plugs in a 2016 fs44? Thanks in advance
-
What are the two adjustments located to the right of the driver control on the stereo?
-
FS33 Cover
Pildo replied to stoked's topic in Centurion Boat Maintenance, Performance, Troubleshooting
My fs44 cover is built by outer armor -
SV230 hard start
Pildo replied to MCs 230's topic in Centurion Boat Maintenance, Performance, Troubleshooting
I am having the same issues with a 2006 sv230. Also replaced the iac motor and filter. Actively following this post and open to try ideas. -
Over heating at idle
Pildo posted a topic in Centurion Boat Maintenance, Performance, Troubleshooting
My 2006 Enzo with 5.7 black scorpion is over heating at idle. I already changed the impeller and checked the screen at the transmission cooler. When I give it some throttle it goes back to regular temp. Any ideas out there? -
Over heating at idle
Pildo replied to Pildo's topic in Centurion Boat Maintenance, Performance, Troubleshooting
Having the plate machined down seemed to do the job