Leaderboard

Finally got the time to sit down and do a more detailed write up. Myself and a friend installed the SV version of these InfinityWave surf tabs on my 2014 Centurion SV244, we installed the tabs one evening and then I ran and finished the wiring a couple nights later on 04/13. Since the weather was crappy that weekend, my first LAKE TEST was on the evening of 04/17/2019. I can honestly say that my expectations were exceeded and after only 2-3mins, I had found the right deployment angle to make an excellent surf wave on the regular side. We only had a couple hours and myself and 2 buddies spent it surfing. I totally forgot to see what goofy wave looked like or get any pics or video without a surfer on the wave. I will do that next time out and post up more information. Initial reaction when getting the InfinityWave tab system….they look and feel very well made, its a beefy system and the finish is very nice. I love the fins on the bottom of the tabs since one thing that concerned me putting tabs on an SV244, is I knew that the factory Quicksurf tabs that were installed on the 2015/2016 models where not up to par and most owners I talked to or heard about preferred to still list the boat for the surf wave since they did not feel like the wave using the tabs had enough push/power. I believe with a deep V boat, the hull wants to direct the water outwards, not back toward the surf wave, so without the fins on the bottom of the tab which help direct the water coming off the bottom of the hull toward the surf wave, you don’t get surf wave that feels like it has power. I have Ramfill on my boat and since its important for the tabs to be up as far as possible under swim platform when retracted, the best position I found puts the actuator bracket mount behind the Ramfill tanks….so rather than run the actuator wire thru the hole in the bracket, I drilled/chamfered a hole for the wire approx. 3.5” toward the center of the boat & 3.5” higher than the bracket position so I could avoid the Ramfill tanks and get access to the wire. Actuator wire is 5/16” diameter, so I drilled a 3/8” hole (starting with smaller bit and running in reverse till well thru gelcoat), after the 3/8” hole was drilled I then got another drill bit slightly larger and ran it in reverse to chamfer the hole so I could avoid spider cracking and remove sharp edges due to wire running thru that (most people will not run into this and can run the wire thru the extra hole in the actuator bracket). Then I ran the wires thru hull and sealed the holes on both inside/outside of the hull. I then ran and zip tied all the electrical up to the bottom of the top deck along the outer perimeter and ran everything up to the drivers helm carefully concealing the wires and securing them with zip ties. For now, I am just fabricating a temp bracket to mount the switches below the steering wheel for easy access. My Ballast setup on this boat: Ramfill = 1,250 each side for total of 2500lbs. PnP bags in each rear locker at 700lbs each for total of 1400lbs. PnP bag under bow seats is 500lbs. Then I also have 500lbs of lead bags, I place 300lbs under the bow filler cushion and the other 200 lbs to the left of drivers feet on the floor against the built-in cooler. I fill the Ramfill tanks to 100% on both sides and then I DRAIN off the non-surf side Ramfill to 80% to give a slight list to boat. So basically 1250 Ramfill on surf side and 1000 Ramfill on non-surf side which gives a total of 4,650lbs of ballast. In video’s I posted links too above were taken on 04/17, total of 3 guys on boat including the surfer. Speed is 11mph and center trim tab is at 40%. PCM ZR409 engine at 800ft elevation and my rpm was at 3,150. Previously I ran the same ballast set up but used Nauticurl suck gate and with all things the same, my rpm was at 3,400, so using these InfinityWave surf tabs brought the rpm’s down for sure. Love that since its easier on the engine and I will save a little gas money to boot. Extremely happy with my purchase and wanted to post my experience since I know others are looking at these tabs and probably have similar initial hesitation like I did since these tabs are fairly new to market. Combine the performance of these tabs which I can now experience behind my boat with the great price and customer service and you have a winner!

It's great that you are happy with your tabs. I worked hard on the design with a lot of prototypes.

Took delivery of our ZS232 a couple weeks ago.